AMP Research PowerStep XTreme Power Running Boards2008to 2016 Ford F-250/350/450
SKU78234-01A
No reviews
Sale
Sale
Original price
$2,199.99
-
Original price
$2,199.99
Original price
$2,199.99
+ Free Shipping
$2,199.99
-
$2,199.99
Current price
$2,199.99
| /
Availability:
Only 4 left!
Estimated Deliveryin 1-5 business days
Guaranteed Fit
This fits your truck or your money back
Free Shipping
Orders Over $350, Lower 48 States
No Sales Tax
No sales tax on all orders (except AZ & CA)
Full Manufacturer Warranty
If anything goes wrong your covered
Overview
The AMP Research PowerStep XTreme is the dual-motor build of the PowerStep, made for trucks that live in road salt, mud, and hard weather. Open a door and the board swings down to step height on its own. Close the door and it retracts against the rocker panel after a three second delay, so there is a real step when it is needed and nothing hanging low when it is not.
What separates the XTreme from a standard PowerStep is the drivetrain. Two motors per side instead of one, driving a rigid cast aluminum board on corrosion-resistant stainless steel hinge pins. That second motor per side is what AMP Research points to for trucks that frequent or live in areas with extremely harsh climates. The aluminum components are anodized before a military-grade PTFE coating goes on, guarding the underlying aluminum against corrosion. The step surface is 6 inches wide, textured black powder coat, and runs the length of the cab, so a work boot gets a real footprint instead of a narrow bar to balance on. From the brackets to the boards, each PowerStep XTreme running board carries a 600 lb load capacity.
Key Benefits
Dual-motor design - Two motors per side instead of the single motor on other PowerStep variants, which is what AMP Research points to for trucks living in extremely harsh climates.
600 lb load capacity - Rated 600 lb per board, from the brackets to the boards, on rigid cast aluminum with corrosion-resistant stainless steel hinge pins.
Anodized and PTFE coated - The aluminum components are anodized before a military-grade PTFE coating is applied, guarding the aluminum underneath against corrosion.
6 inch step surface - An extra wide, textured, slip-resistant step that runs the length of the cab and suits any type of footwear, wet or dry.
Lower deployed step - Drops much lower than a stationary running board, which rests 1 to 2 inches below the body and is often still too far from the ground to be convenient for many passengers.
Integrated LED lighting - Two pair of LED lights wash the running board and the ground below, switching on when the steps deploy and off when they retract.
How It Works
The PowerStep XTreme is powered, not manual, and it takes its cue from the doors. Open a door and the linkage drives the board down and out to step height. Close it and the board retracts against the rocker panel after a three second delay. There is nothing to pull, fold, or remember.
Power comes through an OBD-II connection. On newer applications the module connects straight to the OBD-II port through a Plug-N-Play harness, which simplifies the electrical side of the install. An Override Switch is available separately for manual control of the boards.
The steps can also be parked in the deployed position by hand. Open the door, place a foot on the step, and keep firm pressure on it while the door closes, and the boards stay down.
Keeping the Linkage Clean
Mud, dirt, and road salt collect in the mechanism of any powered board, and trapped debris is what causes noise or binding. AMP Research calls for cleaning the front and rear linkages, all four hinge points, with a pressure washer, while avoiding spraying the motors directly. After washing, apply silicone spray, dry film lubricant only, to all four linkage arms and every pivot pin, including the pins located high on the linkage arm, then cycle a door to work the lubrication into the hinge points. Do not lubricate with greases, oils, WD-40, or penetrants, and do not apply silicone, wax, or protectants to the running board itself. Do this periodically, or any time mud, dirt, or salt becomes trapped in the mechanism.
Specs
Brand
AMP Research
Type
Running Board
Material
Aluminum
Weight Rating
600 lbs
Warranty
5 Year Limited Warranty
Finish
Textured Black Powder Coat
Installation
The XTreme is a vehicle-specific kit that mounts to the rocker panel, and AMP Research calls the installation straightforward: all hardware, bracketry, and vehicle-specific instructions are included in the box. Where the truck supports it, the Plug-N-Play module handles the OBD-II connection instead of a hunt through factory wiring.
The gotcha is that some drilling is required, as is some splicing of wires, so AMP Research recommends professional installation. The video installation guide below walks through the job on a truck.
What's Included
Vehicle-specific mount kit with bracketry and hardware
Vehicle-specific installation guide
Plug-N-Play OBD-II module on newer applications that use it
The Override Switch is an optional accessory for manual control and is not part of the kit.
About AMP Research
AMP Research builds powered truck steps and running boards, and the PowerStep line is what the brand is known for. AMP Research is a RealTruck company. Like all PowerStep products, the PowerStep XTreme is backed by a 5 year limited warranty covering defects in materials or workmanship on product properly installed per the provided instructions. That term runs five years from the date of purchase and stays with the original purchaser, and it ends if the boards are removed from the original vehicle or the vehicle is transferred to another owner. Damage from misuse, abuse, accident, improper installation, modification, or inadequate maintenance is not covered, which is another reason the cleaning routine above is worth keeping up.
How It Compares
Feature
AMP Research PowerStep XTreme Power Running Boards
AMP Research PowerStep Power Running Boards
AMP Research PowerStep XL Power Running Boards
Product type
Power-retractable running board
Power-retractable running board
Power-retractable running board
Motor design
Dual-Motor, two motors per side
Single motor per side
Single motor per side
Construction
Cast aluminum, stainless steel hinge pins
Cast aluminum, stainless steel hinge pins
Cast aluminum, stainless steel hinge pins
Corrosion protection
Anodized with military-grade PTFE coating
Anodized with military-grade PTFE coating
Anodized with military-grade PTFE coating
Step surface
6 in wide, cab length, textured black powder coat
Non-slip cab-length step
Non-slip step, larger board footprint
Lighting
Integrated LED convenience lights
Integrated LED convenience lights
Integrated LED convenience lights
Operation
Auto deploy with door, optional override switch
Auto deploy with door, optional override switch
Auto deploy with door, optional override switch
Best for
Harsh climates, salt, mud, heavy daily cycling
Everyday truck and SUV step access
Buyers who want a larger step board
Key Facts
Rated to hold 600 lb per board.
Dual-Motor drive uses two motors per side, where every other PowerStep model runs one motor per side.
Step surface is 6 inches wide and runs the full length of the cab, finished in textured black powder coat.
Cast aluminum components are anodized and then coated in military-grade PTFE for corrosion resistance.
Backed by AMP Research's 5 Year Limited Warranty from the date of purchase.
Frequently Asked Questions
What makes the PowerStep XTreme different from the standard PowerStep?
The XTreme runs a Dual-Motor design with two motors per side, while the other PowerStep models use a single motor per side. That second motor is what earns the XTreme name, giving you more drive strength and redundancy on trucks that see road salt, mud, deep cold, or heavy daily cycling. Everything else in the family shares the same cast aluminum build and LED-lit step, so the motors are the real decision point.
What is the PowerStep XTreme made of and how is it finished?
The boards use rigid cast aluminum construction with stainless steel hinge pins. All aluminum components are anodized and then finished with a military-grade PTFE coating to guard against corrosion and surface wear. The step face itself is a textured black powder coat, 6 inches wide, running the length of the cab for a slip-resistant surface in wet or icy conditions.
How much weight will the PowerStep XTreme hold?
Each board is rated at 600 pounds, so it handles a big guy in work boots with gear in hand without complaint. The rating is per the manufacturer and assumes the boards are installed to the vehicle-specific instructions and mounted to the rocker panel with the supplied brackets. If you are unsure whether your install is correct, call or text Truck Bed Barn at (623) 272-6510 before you load them up.
How does the PowerStep XTreme install and does it need wiring?
The kit is vehicle-specific and includes the mount brackets, hardware, and an installation guide. On newer applications a Plug-N-Play harness connects straight to the OBD-II port, which cuts most of the wiring work out. Some applications still require drilling and wire splicing, so AMP Research recommends professional installation. Truck Bed Barn can walk you through what your specific truck needs before you order.
Do the boards work in snow, mud, and road salt?
That is the environment the XTreme was built for, and the anodized and PTFE-coated aluminum is what keeps corrosion off the hardware. Debris such as mud, dirt, and road salt can pack into the linkage and cause noise or binding, so periodic cleaning is part of ownership. Pressure wash the four linkage hinge points, avoid spraying the motors directly, then hit the linkage arms and pivot pins with dry silicone spray lubricant.
What warranty comes with the PowerStep XTreme?
AMP Research backs the PowerStep XTreme with a 5 Year Limited Warranty covering defects in materials and workmanship when the product is installed per the provided instructions. The coverage runs five years from the date of purchase, stays with the original purchaser, and ends if the boards are removed from the original vehicle or the vehicle changes owners. Truck Bed Barn is an authorized dealer and can help you start a claim at (623) 272-6510.
Can I control the boards manually instead of with the doors?
Yes. The boards deploy and retract automatically with the doors out of the box, and an optional PowerStep Override Switch is available if you want manual control, for example to hold the boards retracted off-road or keep them out on a job site. The integrated LED convenience lights fire when the steps deploy either way. Ask Truck Bed Barn to add the override switch to your order if you want it in the same box.
Fitment
PowerStep XTreme boards are built vehicle-specific, not universal. Board length, bracketry, and harness type all change from one application to the next, so a kit built for one truck will not bolt to another. Coverage spans a wide range of trucks, but availability is not identical across every year, model, and cab configuration, and the newer Plug-N-Play OBD-II connection is application dependent.
Exact fitment gets confirmed per vehicle before anything ships. Have the year, make, model, and cab configuration ready and confirm the application before ordering, and the kit that arrives is the one built for that truck.
Call or text Truck Bed Barn with the truck details to lock in the right PowerStep XTreme kit, or add it to the cart and fitment gets verified before the order goes out.
Not sure it fits your truck? Chat or call our team at (623) 272-6510 before you order to activate our Fitment guaranteed Promise.
Fitment
Shipping Policy
At Truck Bed Barn, we aim to make shipping clear, simple, and reliable. Below you’ll find everything you need to know about how and where we ship your order.
Shipping Coverage:
We currently ship to customers within the United States, excluding Alaska and Hawaii. At this time, we do not offer international shipping.
Shipping Costs:
We offer free standard shipping on all orders shipped within the United States, excluding Alaska and Hawaii. There is no minimum purchase requirement.
Order Processing Time:
Orders are typically processed within 0–2 business days (Monday-Friday 9:00AM - 5:00PM MST,). Orders placed after our daily cutoff may begin processing the next business day.
Please be advised that processing times may vary by brand. Any exceptions are outlined below.
Estimated Delivery Time:
Once your order ships, delivery generally takes 1–5 business days, depending on your location and carrier.
Total estimated delivery time: 1–7 business days from the date your order is placed.
Please be advised that shipping times may vary depending on the brand and whether the item is made to order. For more accurate timelines, refer to the brand-specific shipping estimates outlined below.
Brand Specific Shipping Times:
Fas-Top Products: Orders ship within 14–20 business days. Transit time is 1–7 business days. Estimated total delivery time: 15–27 business days.
Carriers
We work with trusted national carriers to ensure safe and timely delivery. Carrier selection may vary based on package size, destination, and availability. Your items are shipped from our warehouse through reputable carriers, including USPS, UPS, and FedEx.
Tracking Information
Once your order ships, you’ll receive a confirmation email with a tracking number. You can use this to monitor your shipment’s progress at any time with the Track my order page.
Delivery Issues
If your order is delayed, lost, or arrives damaged, please contact our customer support team as soon as possible. We’ll work with the carrier to resolve the issue quickly. You can email us at help@truckbedbarn.com or call (623)272-6510 during Monday-Friday 9:00AM - 5:00PM MST.
Questions?
If you need additional shipping details or assistance, please visit our FAQ page or contact our support team directly.
Contact Information
Store Name: Truck Bed Barn
Address:704 S Myrtle Ave, Unit 2209, Tempe, AZ 85281
Customer Service Hours: Monday-Friday 9:00AM - 5:00PM MST
Response Time: We aim to reply within 24 business hours.
Returns & Refunds
At Truck Bed Barn, your satisfaction comes first. If something isn't right with your order, we make returns simple and stress-free.
30-Day Returns:
You have 30 days from the day your order arrives to start a return. To qualify, items need to be unused, uninstalled, in the same condition you received them, and packed back up with their original box, hardware, and any included accessories. Our truck experts are happy to walk you through each step. We never charge a restocking fee on any return.
Return Policy Summary:
Return window: 30 days from delivery to begin your return.
Condition: Items must be unused, uninstalled, and returned in original condition with all packaging, hardware, and accessories.
Help when you need it: Our team guides you through the whole process.
Restocking fee: None, ever.
Return Shipping Costs:
Defective, damaged, or incorrect items: No cost to you. This covers anything that arrives damaged by the carrier, defective, or different from what you ordered. We will provide a prepaid return label.
Change of mind or wrong item ordered: You are responsible for the actual return shipping cost. This applies when an item does not fit, you ordered the wrong one, or you simply no longer want it. Original shipping charges are non-refundable.
How to Start a Return:
Reach out: Emailhelp@truckbedbarn.comwith your order number and a quick note about why you are returning the item.
Repack it: Put the item back in its original packaging along with all hardware, accessories, and paperwork.
Ship it back: Follow the instructions in your return authorization email. For defective, damaged, or incorrect items we will include a prepaid label. For change-of-mind or wrong-item returns, you will arrange and cover the return shipping.
How Refunds Work:
Once your return reaches us, we inspect it to confirm it meets the conditions above. After it is approved, we issue your refund to your original payment method. Depending on your bank or card provider, the credit usually appears within 5 to 10 business days.
Exchanges:
Need a different cover, size, or product instead? Just email help@truckbedbarn.com and we will set up a fast exchange for you.
Items We Can't Accept Back:
-Rugged Liner Products
-Trail FX Truck Bed Liners
A small number of products are non-returnable, including custom or special-order covers. Any item like this is clearly marked as non-returnable right on its product page.
